Anybody seen this T-Handle shifter?

Discussion in 'SRT Product Line General Discussion' started by NetNathan, May 30, 2009.

  1. NetNathan

    NetNathan Not the Momma

    Messages:
    1,790
    Likes Received:
    0
    Joined:
    Nov 9, 2007
    Location:
    Corona, CA
    Last edited: May 30, 2009
  2. SRTLUVR

    SRTLUVR Detailing "Go-to" Guy

    Messages:
    3,018
    Likes Received:
    0
    Joined:
    Nov 6, 2007
    Location:
    Birmingham, AL
    Good lookin piece, not too shabby at all. If I wasn't so damn loyal to Billet Technology, I'd probably get it!! :)
     
  3. NetNathan

    NetNathan Not the Momma

    Messages:
    1,790
    Likes Received:
    0
    Joined:
    Nov 9, 2007
    Location:
    Corona, CA
    BT should make a more rounded version..

    ..
     
  4. SRT8U

    SRT8U Supporting Vendor

    Messages:
    1,726
    Likes Received:
    0
    Joined:
    Nov 7, 2007
    Location:
    S Florida
  5. NetNathan

    NetNathan Not the Momma

    Messages:
    1,790
    Likes Received:
    0
    Joined:
    Nov 9, 2007
    Location:
    Corona, CA
    Have BMC check to see if it will fit the earlier LX platforms. It should.
     
  6. Cam

    Cam Management up n smoke

    Messages:
    2,693
    Likes Received:
    0
    Joined:
    Nov 15, 2007
    Location:
    Riverside, CA

    It should fit with no issue Nathan, the only dif is they no longer use a knob that threads to the shaft, but the diameter is the same, 8mm.
     
  7. SRT8U

    SRT8U Supporting Vendor

    Messages:
    1,726
    Likes Received:
    0
    Joined:
    Nov 7, 2007
    Location:
    S Florida
    I know it will fit the newer ones, just not sure about the 06-07's with the screw type fitting.
     
  8. NetNathan

    NetNathan Not the Momma

    Messages:
    1,790
    Likes Received:
    0
    Joined:
    Nov 9, 2007
    Location:
    Corona, CA
    My MOMO Super Anatomic shifter is not using the existing threads either.
    (yea MOMO...fu if you don't like it, I do)

    The MOMO uses a rubber adapter that the set screws go into and push the rubber against the shaft. I had to custom fit one of the rubber adapters to work, but it was simple, and I got it set to a good height. It is a very tight fit and will not slip.


    But I really like this old school type Mopar T-Handle, especially how the Mopar logo is done and even bigger plus is it makes the shaft look beefier. In the beginning I tried ot get BT to round theirs out more, but I know that is a lot of design and machine labor plus material loss.

    ..
     
    Last edited: May 30, 2009
  9. Cam

    Cam Management up n smoke

    Messages:
    2,693
    Likes Received:
    0
    Joined:
    Nov 15, 2007
    Location:
    Riverside, CA
    Welp, if there is anything I can do to help, just ask. I can make anything fit.
     
  10. 1FST4DR

    1FST4DR Supporting Vendor

    Messages:
    2,051
    Likes Received:
    0
    Joined:
    Oct 14, 2007
    Location:
    Ft Laud
    It will fit with no issues.Just slide it over the top and use the set screw.
     
  11. NetNathan

    NetNathan Not the Momma

    Messages:
    1,790
    Likes Received:
    0
    Joined:
    Nov 9, 2007
    Location:
    Corona, CA
    Okay...
    You make the shifter with shaft and I'll give you the $100 for it.
    I rather do that than give to some un-known at Ebay.





    About that Ebay comment...You do take paypal, right?....lol

    ..
     
  12. Cam

    Cam Management up n smoke

    Messages:
    2,693
    Likes Received:
    0
    Joined:
    Nov 15, 2007
    Location:
    Riverside, CA
    I can make the shaft no problem. But on my machine, that shifter would take me HOURS, sorry dude, not a chance. What I can do easlier is modify the mounting system and do something very cool with it. And as far as cost, man, I get real thirsty working the mill. :beer:


    Did you ever see my shifter??.

    I can do the symetrical stuff fairly easy. What I can't do is compound cutting with out taking for ever. Sorry brudder, big difference between a 50K machine and a 5K.


    [​IMG]

    [​IMG]
     
  13. HEMI911

    HEMI911 Platinum Supporting Member

    Messages:
    884
    Likes Received:
    0
    Joined:
    Jun 7, 2008
    Location:
    Vacaville, CA
    That looks awesome Cam!!
     
  14. Cam

    Cam Management up n smoke

    Messages:
    2,693
    Likes Received:
    0
    Joined:
    Nov 15, 2007
    Location:
    Riverside, CA
    Thanks!.
     
  15. bigsteam

    bigsteam neighborenvy20inchstrong

    Messages:
    7
    Likes Received:
    0
    Joined:
    May 20, 2009
    Location:
    seattle native
    These units are not threaded, they are pressure fit like the stock knobs, and tension set
    with a set screw. Tricky to get stock one off, but they are really nice....!
     
  16. NetNathan

    NetNathan Not the Momma

    Messages:
    1,790
    Likes Received:
    0
    Joined:
    Nov 9, 2007
    Location:
    Corona, CA
    That is a hot looking shifter setup Cam.